NIMモジュール, NIM電源ほか関連製品

周波数源または発振器

Frequency Source or Oscillator

シングルサイクルパルサー

Single Cycle Pulser

トリガーパルス源

Triggerable Pulse Source

ゲート発振器

Gateable Oscillator

ゲートジェネレーターまたはパルスジェネレーター

Gate or Width Generator

ディレイジェネレーター

Delay Generator

ダブルパルサー

Double Pulser

4出力パルサー

Four-Output Pulser

仕様

Frequency

B: 外部トリガー, 0Hz から 50MHz

External trigger, 0Hz to 50MHz

C: フロントパネルのプッシュボタンによるシングルサイクル

Single cycle by front panel pushbutton

Delay

Less than 25nsec to 1sec in 9 ranges, continuously adjustable.

Width

Less than 20nsec to 1sec in 9 ranges, continuously adjustable.

Positive Output

B: 振幅: 500mV から 5V まで連続調整, 50オーム(TTL logic)

Amplitude: 500mV to 5V continuously adjustable into 50 Ohms (TTL logic)

C: 立ち上がりおよび立ち下がり時間 5nsec 未満

Rise and fall time less than 5nsec

Negative Output

B: 立ち上がりおよび立ち下がり時間 3.5nsec 未満

Rise and fall times less than 3.5nsec

Duty Factor

Greater than 50% each output, in complementary pulse mode duty factors larger than 90% may be attained

Trigger Out Positive

Positive +1.1V square wave into 50 Ohms

External Trigger

Requires positive l V, with rate of rise greater than 3V/usec

Waveform Distortion

Less than 5% at full amplitude.

External Gate

Synchronous or asynchronous; switch selectable. Requires a positive 1.5 V signal

Single/Double Pulse

Switch selectable, minimum double pulse spacing of 20nsec. Pulse separation set by delay controls

Jitter

Repetition rate, delay or witdh, 0.1% +50psec

Mechanical

Double witdh AEC module, 2.7" wide x 8.7" high in accordance with TID-20893 (Rev. 3)

Weight

3 1/2 lbs., net; 7 lbs., shipping.

Power Requirements

B: +12V @80mA, -12V @100 mA, +6V @300mA, 内部にて選択, 側面パネルを外しスライドスイッチをどちらかの位置にすることで設定可能

+12V @80 mA, -12V @100mA, +6V @300mA, selectable internally. Easily changed by removing side and throwing slide switch into either position

Frequency

10Hz to 1MHz, continuously adjustable.

External Trigger Requires

Single Cycle

One pulse occurs each time the push button is pressed.

Single/Double Pulse

最小分離 50nsec

This toggle provides for a pulse pair whose separation is varied by the delay controls.

Minimum separation is 50nsec

Rise Time of Output (10-90%)

20nsec to 50usec (in 11 steps), exponential shape and independent of decay time.

Decay Time Constant of Output(100-37%)

50nsec to 1000usec (in 11 steps), exponential shape and independent of risetime for decay/rise time >10.

Trigger Out

Positive 3 volt pulse, 10nsec rise time, 0.2usec witdh, 50 ohms output impedance.

Delay

-50nsec advance to 10msec delay (between Trigger Out and leading edge of output pulse).

Output Amplitude

Zero to 9.99 volts maximum. Adjustable by ten-turn potentiometer.

Attenuator

 X10 および X100, 1000:1 まで

X10 and X100 providing up to 1000: 1.

Integral Linearity of Output

Duty Factor Effect

Amplitude shift less than 0.1% below 30% duty factor. Duty factor in percent for tail pulses is defined as: (8 decay time constants/pulse spacing) X100.

Output Polarity

Positive or negative.

Output Impedance

External Reference Input

+/- 15 volts max.

Jitter of Frequency and Delay

Less than 0.1%.

Temperature Coefficient of Output

Less than 0.03%/deg C.

Amplitude Jitter (Resolution)

Power Required

+24V at 50mA, -24V at 50mA, +12V at 175mA, -12V at 80mA.

Mechanical

Double-witdh AEC module, 2.70 inches wide by 8.70 inches high. Conformsto AEC Report TID-20893 (Rev. 2).

Count Rate

10Hz to 1MHz, continuously adjustable

Mode

Random or Repetitive

Random Distribution

Poisson for intervals greater than 1.40usec

Pulse Shape

Tail pulse with independently adjustable rise and fall times

Pulse Amplitude (STEP) Characterization

b) ジッター(解像度): 0.01% RMS

Jitter (resolution): 0.01% RMS

c) 温度指数: +/-0.02%/deg C

Temperature Coefficient: +/-0.02%/deg C

Frequency Jitter (Repetitive Mode)

Less than 0.1%

External Trigger

Requires 1V positive pulse. Input impedance 1K

Trigger Out

Positive 3V pulse, 20nsec rise time, 100nsec width, 50 ohm output impedance

Rise Time of Outputs (10-90%)

0.1usec - 20usec in 8 steps

Decay Time Constant (100-37%)

5-1000usec, in 8 steps. Rise and Decay time independent of each other for Decay Time/ Rise Time > 10

Output Amplitude Ranges

Repetitive only; +/- 1V max from 50?ohm source. adjustable by ten-turn potentiometer from zero to maximum.

Normalize

Output Impedance

Positive/Negative

Attenuation

4 step attenuators of X2, X5, X10 and X10 for a maximum of X1000

+10V Max; 10K input impedance

Power Requirements

+/- 24V at 65mA, +12V at 140mA, -12V at 40mA

Mechanical

Double witdh AEC module, 2.7" wide x 8.7" high in accordance with TID-20893 (Rev. 3)

Weight

3 1/2 lbs., net; 7 lbs., shipping.

Rep Rate

2.0Hz to 500kHz

Width

100nsec to 1msec

Delay

250nsec to 10msec

Rise Time

50nsec to 10usec (10 % - 90 %) in 8 steps

Decay Time

0.5usec to 1.0msec (100 % - 37 %) in 11 steps

Amplitude

0.0 to 10.0V (0 to 5 V into 50 ohms)

エネルギー単位を選択(keV)

Scaleable in energy units. (keV)

Resolution

Jitter

Attenuation

Integral non-linearity

Temperature stability

+/- 5ppm per deg C from 20 deg C to 45 deg C

Pulse Type

- テールモード, 立ち上がり時間 50nsec(固定), 減衰時間調整可能

- フラットトップモード, 立ち上がり時間と減衰時間の両方を調整可能

Flat-top or Tail pulse - In tail mode, rise time is a fixed 50 ns, decay time is adjustable. In flat-top mode, both rise time and decay time are adjustable

Polarity

Positive/Negative

Ext. Trigger

0 to 500kHz, +100mV to +3.5V, threshold adjustable

Width

100nsec to 1msec

Modes

シングルパルス, 内部繰り返し周波数, 外部トリガー,

Ext Trigと同じパルス要求の外部ゲート

ランプ調整可能な内部スタートポイント/ストップポイント, 調整可能なランプ周期30?900秒, 選択可能なランプサイクル数を keVまたはボルトで上昇, パルス発生前にベースラインをゼロにするための固定ベースラインオプション

Single pulse via a front panel pushbutton;

Internal Rep Rate;

External Trigger;

External Gate with the same pulse requirements as Ext Trig;

Internal Ramp-adjustable start and stop points; adjustable ramp period 30-900sec, selectable number of ramp cycles, ramp in keV or volts. Clamped baseline option to bring the baseline to zero prior to the next pulse.

Remote

RS232 at 9600 baud, User Customized or LabView Drivers.

Power Required

-24V, 150mA

+12V, 450mA

-12V, 5mA

可搬性を要する用途またはベンチトップで使用する場合, ポータブル電源を使用できます, Model AP-3 ポータブルNIM電源を併せて参照ください

Portable power supply available for applications that require portability or benchtop use. See BNC Model AP-3 Portable NIM Power Supply.

Mechanical

Triple-witdh AEC NIM module 4.05" wide x 8.70" high in accordance with TID-20893 ( Rev 3. ).

Weight

2 lbs. 13 oz. net, 6 lbs shipping.